News Center
News Center

Follow the company news, focus on the latest industry trends

The protection of hard inorganic fiber spraying and the introduction of the matters needing attention

2019-04-23

The operation procedures of hard inorganic fiber spraying are complicated, and we need to do a good job of protection and grasp the relevant matters needing attention when operating. First of all, we should do a good job of ventilation for the insulation and sound absorption layer after spraying, and also provide a dry environment. In general, its average temperature can be set at twenty-five degrees Celsius, and the humidity needs to be less than 61%. Its curing time should be fixed according to different thicknesses, and the fixed time can be adjusted between 24 hours and 72 hours, so that other decorative lights can be continued. In the spraying we do

Key words:

Insulation material

The protection of hard inorganic fiber spraying and the introduction of the matters needing attention

Superfine inorganic fiber spraying base construction

2019-04-23

1. The quality of the base should meet the following requirements: the base should be firm, no cracking, no powder, no sand, no hollowing, no peeling, no lime burst point and no poor adhesion of the old coating, metal material surface without corrosion peeling, etc.; 2. The base should be clean, the surface shall be free of dust, laitance, oil, rust, mildew, salt precipitates, moss and other sundries, and there is no need for plastering and batch putty treatment; 3. The base course shall be checked and accepted before spraying, and spraying construction can be carried out after it is qualified.

Key words:

Insulation material

Superfine inorganic fiber spraying base construction

Determine whether a thermal insulation material is suitable for the project.

2019-04-22

The inorganic fiber spray cotton in the sound-absorbing spray product is a three-dimensional network structure, which can attenuate the sound wave energy, so it has good sound absorption performance. 25mm Noise Reduction Coefficient (NRC)= 85%,50mm Noise Reduction Coefficient (NRC)= 100. Most of the basement ceiling installation of a large number of hanging parts and piping complex. Therefore, whether it is before or after the installation of the pipeline, the construction of traditional profile insulation will feel that there are great difficulties in the construction. There are complex elevator lifting equipment inside the elevator shaft, the traditional insulation and noise reduction materials are difficult to construct, if the construction on the outside of the elevator will reduce the effective.

Key words:

Insulation material

Determine whether a thermal insulation material is suitable for the project.

Precautions for the use of inorganic fiber spray glue

2019-04-17

Inorganic fiber spray engineering effect is done well, the use of inorganic fiber spray glue play a great role, then, inorganic fiber spray glue in the spraying process should be how construction operation to achieve the best effect. Second, before and after dilution and before use should be fully stirred, master the ratio of water, so that the adhesive force of spraying glue into full play, three, half of the dilution ratio (ratio to water): organic fiber 1:8, mineral wool and glass fiber 1:7 four, in

Key words:

Insulation material

Precautions for the use of inorganic fiber spray glue

Inorganic fiber spraying construction conditions

2019-04-12

Inorganic fiber sprayed cotton itself is a very good new building material, its performance is relatively stable (raw materials for inorganic minerals); can be applied to a wide range of (gymnasiums, bars, KTV, workshops, computer rooms, theaters, conference rooms, subways and other places can be applied). However, the performance of materials in the system depends on other parts, such as construction price adjustment, accurate on-site matching of materials, etc. If these materials are not in place, good materials may also become failures in the system. Inorganic fiber spraying construction conditions: 1. grass-roots quality assurance 1, grass-roots quality should be solid, no powder, no sand

Key words:

Insulation material

Inorganic fiber spraying construction conditions

Four characteristics of inorganic fiber spraying:

2019-04-12

Four characteristics of inorganic fiber spraying: 1. thermal insulation ※ Ultrafine inorganic fiber spraying is a kind of energy-saving thermal insulation material with high thermal insulation performance. Thermal conductivity λ = 0.038 W/m • K, in a class of non-combustible insulation materials, thermal insulation performance ranking in the forefront of many building insulation materials. 2. the whole seamless ※ ultra-fine inorganic fiber sprayed thermal insulation layer forms a skin-type whole, airtight without seams, effectively blocking the thermal bridge, fundamentally solving the problems of traditional thermal insulation profiles such as many seams, easy to fall off and deform, and not firmly pasted with the substrate, and greatly improving the protection of the building envelope.

Key words:

Insulation material

Four characteristics of inorganic fiber spraying:

Inorganic fiber spraying for basement

2019-04-12

The ultra-fine inorganic fiber cotton and fiber spraying special binder through a complete set of professional spraying equipment, after the nozzle port is fully mixed, with a certain pressure evenly sprayed on the top surface of the non-heating room, forming a certain thickness of heat preservation, sound absorption layer process, referred to as inorganic fiber spraying. After natural drying, the formation of a closed, seamless, overall stability, elastic skin-type insulation, sound absorption layer. After spraying, the surface is smooth, the fiber is evenly distributed, and there are no defects such as delamination, holes and cracks that affect the use. At the same time, it has three functions of energy saving and heat preservation, sound absorption and noise reduction, and fire prevention. Inorganic fiber spraying layer is divided into soft inorganic fiber

Key words:

Insulation material

Inorganic fiber spraying for basement

Spraying protection and precautions

2019-04-07

For the thermal insulation and sound absorption layer after spraying, ventilation and dry environment should be provided. Usually, when the average temperature is 25 ℃ and the relative humidity is less than or equal to 60%, the drying and curing time is 24~72 hours according to different thickness, and then other processes such as decoration can be carried out. Before spraying, all kinds of hanging parts of pipelines, air ducts and other equipment shall be installed to avoid drilling and chiseling on the base surface after spraying. During the drying and curing of the finished product, avoid mechanical impact and rain erosion. When the spray coating is damaged due to collision, local repair should be carried out. For parts that are often vulnerable to mechanical collision, it can be pasted.

Key words:

Insulation material

Spraying protection and precautions
< 123 >

Hebei Jinjilina insulation material Co., Ltd.

Telephone: +86- 15803116758

E-mail: 276624183@qq.com

Website: http://www.hbpentumian.cn

Address: Qidi Industrial Zone, Jinzhou City, Shijiazhuang, Hebei Province

If you are using Hebei Jinjilina insulation material Co., Ltd. In the process of the product, please contact us in time if you have any questions, we will treat your every visit, every message, and every feedback with a sincere attitude! Sincerely look forward to cooperating with you!

Hotline:
+86-15803116758

Jinjilina
Business License

Powerby:300.cn  | Tag | Privacy Policy

COOKIES

Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy

COOKIES

Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy

These cookies are necessary for basic functions such as payment. Standard cookies cannot be turned off and do not store any of your information.

These cookies collect information, such as how many people are using our site or which pages are popular, to help us improve the customer experience. Turning these cookies off will mean we can't collect information to improve your experience.

These cookies enable the website to provide enhanced functionality and personalization. They may be set by us or by third-party providers whose services we have added to our pages. If you do not allow these cookies, some or all of these services may not function properly.

These cookies help us understand what you are interested in so that we can show you relevant advertising on other websites. Turning these cookies off will mean we are unable to show you any personalized advertising.